target.h

Go to the documentation of this file.

#pragma once

#define USE_QUAD_MIXER_ONLY 0
#define UNIT_TEST

#define USE_TILT 1
#define LED0_GPIO   GPIOB
#define LED0_PIN    Pin_3
#define LED0_PERIPHERAL RCC_AHBPeriph_GPIOB

#define BEEP_GPIO   GPIOC
#define BEEP_PIN    Pin_15
#define BEEP_PERIPHERAL RCC_AHBPeriph_GPIOC
#define BEEPER_INVERTED

#define USABLE_TIMER_CHANNEL_COUNT 17

#define EXTI_CALLBACK_HANDLER_COUNT 2 // MPU data ready and MAG data ready

#define USE_MPU_DATA_READY_SIGNAL
#define ENSURE_MPU_DATA_READY_IS_LOW

#define USE_MAG_DATA_READY_SIGNAL
#define ENSURE_MAG_DATA_READY_IS_HIGH


#define GYRO
#define USE_GYRO_MPU6050
#define GYRO_MPU6050_ALIGN CW270_DEG

#define ACC
#define USE_ACC_MPU6050
#define ACC_MPU6050_ALIGN CW270_DEG

#define BARO
#define USE_BARO_MS5611

#define USE_MAG 0
#define USE_MAG_AK8975
#define USE_MAG_HMC5883
#define MAG_HMC5883_ALIGN CW270_DEG

//#define USE_FLASHFS
//#define USE_FLASH_M25P16

#define USE_BEEPER 1
#define LED0

//#define SONAR
#define SONAR_TRIGGER_PIN           Pin_0   // RC_CH7 (PB0) - only 3.3v ( add a 1K Ohms resistor )
#define SONAR_TRIGGER_GPIO          GPIOB
#define SONAR_ECHO_PIN              Pin_1   // RC_CH8 (PB1) - only 3.3v ( add a 1K Ohms resistor )
#define SONAR_ECHO_GPIO             GPIOB
#define SONAR_EXTI_LINE             EXTI_Line1
#define SONAR_EXTI_PIN_SOURCE       EXTI_PinSource1
#define SONAR_EXTI_IRQN             EXTI1_IRQn

#define USE_UART1
#define USE_UART2
#define USE_UART3
#define USE_SOFTSERIAL1
#define USE_SOFTSERIAL2
#define SERIAL_PORT_COUNT 8

#ifndef UART1_GPIO
#define UART1_TX_PIN        GPIO_Pin_9  // PA9
#define UART1_RX_PIN        GPIO_Pin_10 // PA10
#define UART1_GPIO          GPIOA
#define UART1_GPIO_AF       GPIO_AF_7
#define UART1_TX_PINSOURCE  GPIO_PinSource9
#define UART1_RX_PINSOURCE  GPIO_PinSource10
#endif

#define UART2_TX_PIN        GPIO_Pin_14 // PA14 / SWCLK
#define UART2_RX_PIN        GPIO_Pin_15 // PA15
#define UART2_GPIO          GPIOA
#define UART2_GPIO_AF       GPIO_AF_7
#define UART2_TX_PINSOURCE  GPIO_PinSource14
#define UART2_RX_PINSOURCE  GPIO_PinSource15

#ifndef UART3_GPIO
#define UART3_TX_PIN        GPIO_Pin_10 // PB10 (AF7)
#define UART3_RX_PIN        GPIO_Pin_11 // PB11 (AF7)
#define UART3_GPIO_AF       GPIO_AF_7
#define UART3_GPIO          GPIOB
#define UART3_TX_PINSOURCE  GPIO_PinSource10
#define UART3_RX_PINSOURCE  GPIO_PinSource11
#endif

#define SOFTSERIAL_1_TIMER TIM3
#define SOFTSERIAL_1_TIMER_RX_HARDWARE 4 // PWM 5
#define SOFTSERIAL_1_TIMER_TX_HARDWARE 5 // PWM 6
#define SOFTSERIAL_2_TIMER TIM3
#define SOFTSERIAL_2_TIMER_RX_HARDWARE 6 // PWM 7
#define SOFTSERIAL_2_TIMER_TX_HARDWARE 7 // PWM 8

/*
#define USE_I2C
#define I2C_DEVICE (I2CDEV_1) // PB6/SCL, PB7/SDA

#define USE_SPI
#define USE_SPI_DEVICE_2 // PB12,13,14,15 on AF5

#define M25P16_CS_GPIO          GPIOB
#define M25P16_CS_PIN           GPIO_Pin_12
#define M25P16_SPI_INSTANCE     SPI2

#define USE_ADC
#define BOARD_HAS_VOLTAGE_DIVIDER
*/

#define ADC_INSTANCE                ADC2
#define ADC_DMA_CHANNEL             DMA2_Channel1
#define ADC_AHB_PERIPHERAL          RCC_AHBPeriph_DMA2

#define VBAT_ADC_GPIO               GPIOA
#define VBAT_ADC_GPIO_PIN           GPIO_Pin_4
#define VBAT_ADC_CHANNEL            ADC_Channel_1

#define CURRENT_METER_ADC_GPIO      GPIOA
#define CURRENT_METER_ADC_GPIO_PIN  GPIO_Pin_5
#define CURRENT_METER_ADC_CHANNEL   ADC_Channel_2

#define RSSI_ADC_GPIO               GPIOB
#define RSSI_ADC_GPIO_PIN           GPIO_Pin_2
#define RSSI_ADC_CHANNEL            ADC_Channel_12

#define LED_STRIP
#define LED_STRIP_TIMER TIM1

#define WS2811_GPIO                     GPIOA
#define WS2811_GPIO_AHB_PERIPHERAL      RCC_AHBPeriph_GPIOA
#define WS2811_GPIO_AF                  GPIO_AF_6
#define WS2811_PIN                      GPIO_Pin_8
#define WS2811_PIN_SOURCE               GPIO_PinSource8
#define WS2811_TIMER                    TIM1
#define WS2811_TIMER_APB2_PERIPHERAL    RCC_APB2Periph_TIM1
#define WS2811_DMA_CHANNEL              DMA1_Channel2
#define WS2811_IRQ                      DMA1_Channel2_IRQn
#define WS2811_DMA_TC_FLAG              DMA1_FLAG_TC2
#define WS2811_DMA_HANDLER_IDENTIFER    DMA1_CH2_HANDLER


#define DEFAULT_RX_FEATURE FEATURE_RX_PPM

#define USE_BLACKBOX 0
//#define ENABLE_BLACKBOX_LOGGING_ON_SPIFLASH_BY_DEFAULT

//#define DISPLAY
//#define GPS
//#define GTUNE
//#define SERIAL_RX
//#define TELEMETRY
#define USE_SERVOS
#define USE_CLI

//#define SPEKTRUM_BIND
// UART3,
#define BIND_PORT  GPIOB
#define BIND_PIN   Pin_11

//#define USE_SERIAL_4WAY_BLHELI_INTERFACE

#define TARGET_BOARD_IDENTIFIER "SITL"
#define U_ID_0 'S'
#define U_ID_1 'I'
#define U_ID_2 'M'


/*
#define USE_QUAD_MIXER_ONLY 0

#define TARGET_BOARD_IDENTIFIER "SITL"
#define U_ID_0 'S'
#define U_ID_1 'I'
#define U_ID_2 'M'

#define ACC
#define USE_TILT 0
#define USE_MAG 0
#define SERIAL_PORT_COUNT 1
*/